F32 Hatch Seal Re-engineering

This forum is for comments and the exchange of information relating to Trojan Boats and boating. Please do not post used parts or boats For Sale in this area. For general, non-boating topics please use our "General Discussions" section.

Note: Negative or inflammatory postings will not be tolerated.

Moderators: BeaconMarineBob, Moderator, BeaconMarineDon

Post Reply
User avatar
jnimety
Registered user
Posts: 13
Joined: Mon Jun 25, 2018 7:18 pm

F32 Hatch Seal Re-engineering

Post by jnimety »

I've been trying to solve an issue with the hatch seals/gaskets on my sort of new to me (my parents bought this boat new when I was 5) 1984 F32. We've always had issues with the foam seals wandering after being replaced. They remain water tight for about a season, then drift and become ineffective.

I finally decided to add aluminum U channel to the hatches to accept the seals and prevent wandering. It's only been a few weeks but I'm very happy with the results. For anyone else interested in doing the same I thought I'd document the process here.

Parts:
  • 24 ft Aluminum Satin Anodized 1-1/6" U-Channel - Amazon
  • 25 ft Water-Resistant Closed Cell Foam Strip, Neoprene-EPDM-SBR, 3/4" Thick, 1" W X 25 ft. L, Black - Grainger
  • 24 Barrel Nuts (8 for each hatch, length less than or equal to hatch thickness, 1/2" in my case) - West Marine
  • 24 pan head screws to match your barrel nuts
  • 24 rubber washers to match your barrel nuts (I cheap-ed out and bought some rubber washers from Home Depot and drilled them out to fit)
Determining the length of cut for the U channel sides took some measuring and If I did this again I'd go about it differently so I won't share the measurements here. If you do attempt this project measure the inside of your hatch opening and use that measurement for the short sides of your mitered u-channel.

One thing I discovered, is that the foam seal contracts longitudinally after removing the paper from the tape. Measure and cut your seals 1 or 1.5 inches longer than needed to avoid gaps.

Now for the reveal!

Image

Image
Image
Image
Image
Joel
1984 F32 "Second Course"
Belle Maer Harbor, Harrison Township, MI
User avatar
RWS
Ultimate User
Posts: 2857
Joined: Sat Feb 18, 2006 7:01 am
Location: West Coast Florida
Contact:

Re: F32 Hatch Seal Re-engineering

Post by RWS »

nicely done

so nice of folks like you to share

its what makes this FORUM GREAT !



RWS
1983 10 Meter SOLD after 21 years of adventures
Yanmar diesels
Solid Glass Hull
Woodless Stringers
Full Hull Liner
Survived Andrew Cat 5,Eye of Charley Cat 4, & Irma Cat 2
Trojan International Website: http://trojanboat.com/

WEBSITE & SITELOCK TOTALLY SELF FUNDED
User avatar
prowlersfish
2024 Gold Support
2024 Gold Support
Posts: 12645
Joined: Sat Nov 05, 2005 6:56 pm
Location: Lower Chesapeake Bay ,Va

Re: F32 Hatch Seal Re-engineering

Post by prowlersfish »

Good info
Boating is good for the soul
77/78 TROJAN F36 Conv.
6BTA Cummins diesels
Life is to short for a ugly boat :D
User avatar
jnimety
Registered user
Posts: 13
Joined: Mon Jun 25, 2018 7:18 pm

Re: F32 Hatch Seal Re-engineering

Post by jnimety »

Thanks!

Here's a pic of the dimensions for the u-channel in case that Amazon link doesn't stand the test of time. I also forgot to add that I decided not to seal the mating surfaces between the aluminum and plastic hatch but may do so in the future. I plan on using 3M Fast Cure 4000 UV for its bonding strength to both plastics and metals.
Attachments
u-channel.jpg
u-channel.jpg (8.8 KiB) Viewed 5397 times
Joel
1984 F32 "Second Course"
Belle Maer Harbor, Harrison Township, MI
User avatar
Captrichc
Moderate User
Posts: 245
Joined: Mon Jul 30, 2018 7:08 pm
Location: Bronx, NY

Re: F32 Hatch Seal Re-engineering

Post by Captrichc »

Amazing. Did you replace the white glass as well?
1974 f32 Sedan
Twin 233 Mercruisers
User avatar
jnimety
Registered user
Posts: 13
Joined: Mon Jun 25, 2018 7:18 pm

Re: F32 Hatch Seal Re-engineering

Post by jnimety »

Captrichc, no. Those are original.
Joel
1984 F32 "Second Course"
Belle Maer Harbor, Harrison Township, MI
User avatar
Captrichc
Moderate User
Posts: 245
Joined: Mon Jul 30, 2018 7:08 pm
Location: Bronx, NY

Re: F32 Hatch Seal Re-engineering

Post by Captrichc »

jnimety wrote: Mon Aug 27, 2018 11:39 am Captrichc, no. Those are original.
Ok thanks. I need to redo my hatches. It's on the list. Along with the hardware.
1974 f32 Sedan
Twin 233 Mercruisers
Post Reply