velvet drive issue

This forum is for comments and the exchange of information relating to Trojan Boats and boating. Please do not post used parts or boats For Sale in this area. For general, non-boating topics please use our "General Discussions" section.

Note: Negative or inflammatory postings will not be tolerated.

Moderators: BeaconMarineBob, Moderator, BeaconMarineDon

topseaturvy
Registered user
Posts: 40
Joined: Tue Aug 14, 2018 9:50 pm

Re: velvet drive issue

Post by topseaturvy »

prowlersfish wrote: Sun Jun 16, 2024 9:26 am If the noise goes away when you raise the rpm, the cause could be a misfire or the dampener plate or both. They will aggravate each other. Even a slight miss can cause a noise. I have fixed many a transition noise issue with a carburetor adjustment.

Maybe 1000-1200 rpm?

As far as getting towed back to the marina, you have 2 engines and a bow thruster so...... But that's your call, not mine.
I'm wondering if 1000-1200 rpm is a bit aggressive for being still tied to the dock. I can probably limp back to the dock with one engine and the bow thruster. The marina will assist with their small tenders to help nudge if necessary. I just don't want to cause extra damage to the drive train.

As in my other post about the spark plugs, maybe replacing them, and cleaning the rotor/cap, might at least alter the noise so I'll know if I'm barking up the wrong tree.

I might just have to bite the bullet and open up the wallet and have a marine mechanic come and do a complete tune up. If that doesn't solve the noise issue at least the mechanic might be able to pin point the noise with a more experienced ear.
mrrudely
Moderate User
Posts: 205
Joined: Sat Jun 08, 2019 11:52 am
Location: Marina Del Rey, CA

Re: velvet drive issue

Post by mrrudely »

I find no joy in this but
my unsolicited opinion remains the same
the transmission is coming out
10 meter mid cabin
User avatar
Moderator
2024 Gold Support
2024 Gold Support
Posts: 306
Joined: Sun Feb 21, 2010 11:48 am
Location: Could be anywhere
Contact:

Re: velvet drive issue

Post by Moderator »

mrrudely wrote: Sun Jun 16, 2024 1:52 pm I find no joy in this but
my unsolicited opinion remains the same
the transmission is coming out
Without hearing it I could not say myself
Moderator

Helping keep Trojan Yachts alive .
Forum Moderator
TrojanBoats.Net
Trojan Boater
User avatar
prowlersfish
2024 Gold Support
2024 Gold Support
Posts: 12707
Joined: Sat Nov 05, 2005 6:56 pm
Location: Lower Chesapeake Bay ,Va

Re: velvet drive issue

Post by prowlersfish »

As far as 1000-1200 in the slip, I don't know your dock or line conditions, but would have no issue with mine. But have seen some I would not.
Boating is good for the soul
77/78 TROJAN F36 Conv.
6BTA Cummins diesels
Life is to short for a ugly boat :D
topseaturvy
Registered user
Posts: 40
Joined: Tue Aug 14, 2018 9:50 pm

Re: velvet drive issue

Post by topseaturvy »

prowlersfish wrote: Mon Jun 17, 2024 9:04 am As far as 1000-1200 in the slip, I don't know your dock or line conditions, but would have no issue with mine. But have seen some I would not.
The dock is in tip top shape. Fairly new, professionally constructed with concrete slabs and a continuous rail for tying off. Fastened with galvanized ready rod about every 3 feet or so going all the way through the rail, then the spacer block and then vertical through 2 x 12's. Even though my boat is a 1985, it has been extremely well maintained over the years. No sign of any issues around the cleats. I not only have spring lines which would act as a back up, but I also have two extra lines running for and aft from the two midship cleats. However on this boat there is only the helm on the bridge. So I might feel more comfortable with an extra hand at the helm, while I check out the noise down in the engine room at such an increased RPM.
topseaturvy
Registered user
Posts: 40
Joined: Tue Aug 14, 2018 9:50 pm

Re: velvet drive issue

Post by topseaturvy »

It would appear Big D and Prowlerfish were on the right track. I replaced the plugs, and cleaned up the rotor and the contact areas in the distributor cap. Both the rotor and the cap were burnt. They both cleaned up pretty good with some 320 grit wet/dry sandpaper though. I fired it up and put it in gear and low and behold the noise was gone.
So thanks guys for convincing me to focus on the running condition of the engine. I'll try and track down a new rotor and a cap. I might as well get two of each and do both engines. I should really see about getting a rebuilt kit for the carb and pull it apart and clean it up.
User avatar
prowlersfish
2024 Gold Support
2024 Gold Support
Posts: 12707
Joined: Sat Nov 05, 2005 6:56 pm
Location: Lower Chesapeake Bay ,Va

Re: velvet drive issue

Post by prowlersfish »

Thats good news.
Boating is good for the soul
77/78 TROJAN F36 Conv.
6BTA Cummins diesels
Life is to short for a ugly boat :D
mrrudely
Moderate User
Posts: 205
Joined: Sat Jun 08, 2019 11:52 am
Location: Marina Del Rey, CA

Re: velvet drive issue

Post by mrrudely »

Congrats!
Very happy that I was wrong!
10 meter mid cabin
User avatar
Big D
Ultimate User
Posts: 2876
Joined: Sat May 01, 2010 10:39 pm
Location: Ontario, Canada

Re: velvet drive issue

Post by Big D »

That's excellent news!
She was a 1969 36 ft wooden beauty with big blue 440s that we'll miss forever.
And thanks to the gang, 2012 Trojan Boater Of The Year
User avatar
P-Dogg
Active User
Posts: 962
Joined: Wed Jun 22, 2011 7:15 pm
Location: Near Baltimorgue, Murderland, where they prove every day that gun control doesn't work.

Re: velvet drive issue

Post by P-Dogg »

Recently had the pleasure of removing my tranny for service. Sharing my engine-supporting solution for my 1985 Tricab in case it's useful.

2x6s with a 2x4 between, supported as required each end. 4" PVC pipe makes it "easy" to slide engine fore n aft.
I needed a less expensive hobby, so I bought a boat!
Post Reply