F32 back deck

Eddie-O · Post by **Eddie-O** » Sun Sep 18, 2011 12:13 am

Am looking for someone who is parting out a f32. need the removable fiberglass section of the back deck . mine is soft and would like to try and replace it rather then try to fix it. I Will also check with Bob

prowlersfish · Post by **prowlersfish** » Sun Sep 18, 2011 8:56 am

Bob was selling some parts of a F32 so you may get lucky .

BTW fixing it is not that hard I had to do it on my F30 . I fliped it over cut the lower glass and removed the core . I replaced it with plywood and reglassed the lower part back on .

Stripermann2 · Post by **Stripermann2** » Sun Sep 18, 2011 9:45 am

Like Paul says...

alexander38 · Post by **alexander38** » Sun Sep 18, 2011 3:34 pm

even if you find used ones they'll most likely will need work.....repairing yours seems to be a dollar wise move..

ready123 · Post by **ready123** » Sun Sep 18, 2011 10:15 pm

Eddie-o wrote:Am looking for someone who is parting out a f32. need the removable fiberglass section of the back deck . mine is soft and would like to try and replace it rather then try to fix it. I Will also check with Bob

Fixing is easy.. do it from underneath, you can use plywood or balsa core.

prowlersfish · Post by **prowlersfish** » Sun Sep 18, 2011 11:11 pm

Didn't someone say that ?

ready123 · Post by **ready123** » Mon Sep 19, 2011 5:48 am

prowlersfish wrote:Didn't someone say that ?

I thought a picture might add to the suggestion.

rossjo · Post by **rossjo** » Mon Sep 19, 2011 11:47 am

Or use Divincyl and never worry about doing it again. Its a bit more expensive than plywood, but doesn't rot!

I've used it with good result s in several areas - you can even glass over the top, sand and paint for a smooth, gel-coat-like finish.

Eddie-O · Post by **Eddie-O** » Mon Sep 19, 2011 11:47 pm

Ready 123 Thanks for the picture if you have more i would like to see them

ready123 · Post by **ready123** » Tue Sep 20, 2011 7:28 am

Eddie-o wrote:Ready 123 Thanks for the picture if you have more i would like to see them

Nothing more on that part but the pulpit was done the same way with Plywood and weights to ensure a good bond before replacing the bottom glass layer, this method allowed for the gel & non skid finish of the top surface to be left untouched...

The fore and side decks were done with balsa core....
http://www.flickr.com/photos/trojanf32/ ... 792002787/

alexander38 · Post by **alexander38** » Tue Sep 20, 2011 6:38 pm

pictures are worth a 1,000 words...of

alexander38 · Post by **alexander38** » Tue Sep 20, 2011 6:42 pm

rossjo wrote:Or use Divincyl and never worry about doing it again. Its a bit more expensive than plywood, but doesn't rot!

I've used it with good result s in several areas - you can even glass over the top, sand and paint for a smooth, gel-coat-like finish.

I looked for this Divincyl, I give, what is it....

Stripermann2 · Post by **Stripermann2** » Tue Sep 20, 2011 6:58 pm

alexander38 wrote:
rossjo wrote:Or use Divincyl and never worry about doing it again. Its a bit more expensive than plywood, but doesn't rot!

I've used it with good result s in several areas - you can even glass over the top, sand and paint for a smooth, gel-coat-like finish.
I looked for this Divincyl, I give, what is it....

Divinycell

http://www.diabgroup.com/europe/products/e_prods_2.html

http://www.boardlady.com/softdeckanalysis.htm

Trojan Boat Forum

F32 back deck

F32 back deck

Re: F32 back deck

back deck

Re: back deck