10 meter mid cabin cockpit upholstery

BobCT · Post by **BobCT** » Fri Mar 02, 2012 10:12 am

Tom - I just PM'd you about the transom piece. I had your email address from last year but lost years worth of email.

Bob

yorklyn · Post by **yorklyn** » Fri Mar 02, 2012 11:14 am

I have a wet bar with no icemaker. hate to say it but i love it. takes up altot of room but i store all my cleaning supplies in it as well as my stern anchor and magma grill . thanks for the pics. haven't had a chance to pull them up yet.

RWS · Post by **RWS** » Sat Mar 03, 2012 7:09 am

gardnersf wrote:I called them today. Their site had just crashed and they didn't know why. I called the guy in Chicago about the wetbar. he is going to get a shipping quote. It may not be too bad as it would go as freight. Now I just need to be sure I want to go that direction.

=============================================

my guess is if you bought all the materials, a stainless bar sink, hinges, cabinet pulls, wiring (use marine grade 120 v STRANDED here) a sheet of formica and bought a new router you would still be cheaper than the shipping

The big cost issue will be the U-line fridge/icemaker. I replaced mine in 2008 or 2009 and it was about $1,100.00

I also keep a tremendous amount of stuff in that wetbar and it is damn convenient too.

The only problem I can see is how to make the curved corners ?

Otherwise building a new one should be a breeze.

RWS

BobCT · Post by **BobCT** » Sat Mar 03, 2012 10:00 am

Scott, the guy that has the 11m w/ the hardtop on craigslist on Long Island had a wetbar last summer. He was asking $1,000 which was way too high and I doubt he sold it. Might be able to save the shipping.

It's the one for $50k and listed all the time.

Bob

Mike Kulp · Post by **Mike Kulp** » Sat Mar 03, 2012 11:09 am

I have the wet bar with the fridge and ice maker and use it all the time, When we vacation on the boat we can keep extra frozen stuff in the ice maker bin, works great. We always have that fridge loaded with drinks and mixers.

yorklyn · Post by **yorklyn** » Wed Mar 07, 2012 7:25 pm

Scott,
Just ordered a bunch of different colored samples of vinyl. Thinking about going pleated white for the coaming pads. I'll post some pics as I get them in.

Todd

Mike Kulp · Post by **Mike Kulp** » Sat Mar 10, 2012 7:48 pm

I took some pictures of my cockpit interior today while working on the boat, please excuse the blue color it is my shrink wrap. my seats are white with maroon piping, this will give you a idea of color and materials

pk · Post by pk » Sun Mar 11, 2012 5:11 am

Awsome!!!

yorklyn · Post by **yorklyn** » Sun Mar 11, 2012 1:39 pm

Mike,
That looks great. I like how you did the piping on the seats, very nice touch! Is that the pleated vinyl that has the "heat welded" pleats? It looks like stiched pleats from the pics.

Mike Kulp · Post by **Mike Kulp** » Sun Mar 11, 2012 2:39 pm

It is heat treated pleats, I left the design up to S S canvas in middle river told him to give it a modern look and do what he wanted. I think it turned out great.

yorklyn · Post by **yorklyn** » Sun Mar 11, 2012 4:39 pm

They did a great job. I really like the work on the helm seats. I just googled them. they're only about an hour and a half from me. Think I will be giving them a call as I get a little closer on my project.

gardnersf · Post by **gardnersf** » Sun Mar 11, 2012 11:54 pm

That looks really nice.

I am going with all white on the cusions. I found a different canvas guy to recover the helm chairs which saved some $. I will be going White\Lt.Grey\White on the coamings. I'm also replacing the vinyl under the radar arch with white.

Teh white is actually slightly off white Nautolex.