Search found 10 matches
- Mon Jun 19, 2017 9:35 am
- Forum: Trojan Boats Forum
- Topic: 1986 Trojan 11M Interior Update
- Replies: 19
- Views: 16952
Re: 1986 Trojan 11M Interior Update
The boat is beautiful and Kudos to you on all the hard work, its certainly paid off! Im looking to do the same, where did you buy most of your vinyl and veneers?
- Tue Apr 26, 2016 3:09 pm
- Forum: Trojan Boats Forum
- Topic: Sling location on 10.8 Meter Convertible
- Replies: 4
- Views: 2640
Re: Sling location on 10.8 Meter Convertible
Its a lift, it has done quite a few large boats, many with the same 13' beam.mikeandanne wrote:Are they lifting your boat with a travel lift or a crane with a spreader??.... because with the crane and spreader care has to be taken on wide boats to keep from pinching them if the spreader is not wide enough....
- Tue Apr 26, 2016 3:08 pm
- Forum: Trojan Boats Forum
- Topic: Sling location on 10.8 Meter Convertible
- Replies: 4
- Views: 2640
Re: Sling location on 10.8 Meter Convertible
Its pretty standard to put the aft sling at the aft bulkhead . Several thoughts I have . 1) are the slings pulling on the rub rail ? 2) Is the bulkhead in good shape not rotted or soft ? . Can the yard use 2 slings one rear spreading load ? some travel lifts are set up this way some are not . I hav...
- Tue Apr 26, 2016 7:26 am
- Forum: Trojan Boats Forum
- Topic: Sling location on 10.8 Meter Convertible
- Replies: 4
- Views: 2640
Sling location on 10.8 Meter Convertible
Hello, I have a 10.8 meter. When I bought the boat there was damage to both sides of the hull right above the rub rail on both sides just aft of the stainless intake grills. It was stress cracks that got worse over the years. An older guy at the marina told me it was from the yard placing the slings...
- Thu Jun 04, 2015 8:43 am
- Forum: Trojan Boats Forum
- Topic: REPLACEMENT A/C
- Replies: 9
- Views: 6566
Re: REPLACEMENT A/C
My aft unit is a reverse cycle 16K BTU cruisair. I too thought the compressor was bad but due to its location I cannot remove it so was about to replace the compressor (2-300$). One last ditch effort was tapping on the compressor with a hammer, it has in the past freed up some stuck compressors. How...
- Sun Apr 26, 2015 7:03 am
- Forum: Trojan Boats Forum
- Topic: Any ideas for 10.8 meter Helm plexiglass??
- Replies: 5
- Views: 4056
Re: Any ideas for 10.8 meter Helm plexiglass??
I have not, which Beacon Marine is it you have a link?prowlersfish wrote:Have you tried Beacon marine ?
Thanks
- Sat Apr 25, 2015 8:33 pm
- Forum: Trojan Boats Forum
- Topic: Any ideas for 10.8 meter Helm plexiglass??
- Replies: 5
- Views: 4056
Any ideas for 10.8 meter Helm plexiglass??
Below is a pic of the faded plexiglass on the helm, Im mainly concerned with the pic of the boat and alarms etc. I took it off to try and polish it up and get rid of the "yellow" but alot of grey paint like stuff chipped and fell right off the back side now you can see straight through it ...
- Fri Jan 30, 2015 9:35 am
- Forum: Trojan Boats Forum
- Topic: 1989 or 1990 Trojan 10.8 meter??
- Replies: 6
- Views: 3980
Re: 1989 or 1990 Trojan 10.8 meter??
Great everyone thanks for the clarity. Now time to get to work on her once i get her home =).
- Wed Jan 28, 2015 12:40 pm
- Forum: Trojan Boats Forum
- Topic: 1989 or 1990 Trojan 10.8 meter??
- Replies: 6
- Views: 3980
Re: 1989 or 1990 Trojan 10.8 meter??
Im guessing 89?
- Wed Jan 28, 2015 9:14 am
- Forum: Trojan Boats Forum
- Topic: 1989 or 1990 Trojan 10.8 meter??
- Replies: 6
- Views: 3980
1989 or 1990 Trojan 10.8 meter??
I just purchased this 10.8 meter sportfish and the title states 89 and the owner swears its a 90 and the Trojan/Bertram plaque on the hull says 1990. Can someone shed some light maybe ?