What do you guys think of this product? NuTeak

This forum is for comments and the exchange of information relating to Trojan Boats and boating. Please do not post used parts or boats For Sale in this area. For general, non-boating topics please use our "General Discussions" section.

Note: Negative or inflammatory postings will not be tolerated.

Moderators: BeaconMarineBob, Moderator, BeaconMarineDon

rossjo
Ultimate User
Posts: 2799
Joined: Tue Nov 08, 2005 2:48 pm
Location: Charleston, SC
Contact:

Post by rossjo »

JGedridge wrote: _________________
1985 36' Trojan Tri-Cabin -- "Viva La Vodka!"
- Sandusky, Ohio
For real? That's your boat's name?
Captain Ross, 2009 Trojan Boater of the Year
"Viva Mahia" F32 Cummins 6BTA diesels,
"Mack Attack" Chaparral 244 Fish, SeaPro 180, McKee 14, Montauk-17
Image
larglo
Moderate User
Posts: 743
Joined: Fri Jul 17, 2009 4:01 pm
Location: Mt Juliet, TN. Percy Prist Lake, Fate Sanders Marina

Post by larglo »

In as much as this is about floor covering, I hope this is not straying from the original post to much, but I have a couple of questions about covering a floor with carpet or wood.

I would like to install carpet on the rear deck, but was wondering about the access panels for the engine and the one in back over the steering gear. How do you cut around the panels, (carpet) and not have it fray around the edges? Is it necessary to glue it to the floor?

Also, I can remember someone having, what appeared to be wood similar to hardwood flooring on the cabin floor. I think it was in an f26, but can't remember who it was. Anyway, the floor in my F25 has a floor that is split in the middle allowing it to be removed, I would think to be able to inspect the bilge.

If the floor is covered in what appeared to be, in a permanent manner, is that permissible to do and not worry about these floor panels being able to be removed in the future?
Checking or replacing a bilge pump comes to mind.

Thaks,

Larry
Larry - 1980 F25 HT

"Lady G"
Mt. Juliet, TN
http://www.photobucket.com/larglo
User avatar
Torcan
Moderate User
Posts: 728
Joined: Tue Dec 21, 2010 7:35 pm
Location: Toronto, Canada

Post by Torcan »

larglo wrote:In as much as this is about floor covering, I hope this is not straying from the original post to much, but I have a couple of questions about covering a floor with carpet or wood.

I would like to install carpet on the rear deck, but was wondering about the access panels for the engine and the one in back over the steering gear. How do you cut around the panels, (carpet) and not have it fray around the edges? Is it necessary to glue it to the floor?

Also, I can remember someone having, what appeared to be wood similar to hardwood flooring on the cabin floor. I think it was in an f26, but can't remember who it was. Anyway, the floor in my F25 has a floor that is split in the middle allowing it to be removed, I would think to be able to inspect the bilge.

If the floor is covered in what appeared to be, in a permanent manner, is that permissible to do and not worry about these floor panels being able to be removed in the future?
Checking or replacing a bilge pump comes to mind.

Thaks,

Larry
you could carpet the area as long as it wasn't permanently held down. You should be able to roll it out of the way if you needed to.
Never, ever block an access door, they are there for a reason. Rolling the carpet out of the way would be my solution, if I was to go that way.
Once you have laid the carpet out and made the template and cuts to fit snug, take it to a carpet dealer and have them edge the carpet. Just like they do for runners, or the small floormats that your car has. They stitch all around so it doesn't fray.

Now back to Nu-Teak

Good points on the heat..although I don't think here in Toronto we have quite the blazing overhead sun you have in the south. Does get hot, but the days of blistering heat are maybe 10-15 a year, the rest is quite bearable. But good point anyways to look into.

I have a sample here at home, I've put suntan lotion on it, it comes out with soap and water, does seem to be stain resistant, or easy to clean up.
Now fishguts and blood, haven't tried that yet :lol:
1980 Trojan F 25 "MY TYME" (sold)
1986 Thundercraft Magnum 280 "The HAILEY-SAVANNAH"
http://www.cbyc.ca/
Captain Blast Off
Sporadic User
Posts: 90
Joined: Tue Jan 11, 2011 10:24 pm
Location: Northern California - Delta

Post by Captain Blast Off »

foofer b wrote:
Captain Blast Off wrote:Nuteak...? :?: I've got old teak... :lol:

Actually That's "Olteak"! And man is it pretty
Sorry man... I didn't spell check :wink:
1963 31' Sea Breeze; Twin Interceptors
2000 21' Lightning; Marine Power 454 jet drive

http://s1177.photobucket.com/home/sdelfino5225/index
mr elevman
Moderate User
Posts: 267
Joined: Tue Dec 18, 2007 8:29 pm
Location: toms river nj

Post by mr elevman »

i picked up 2 sample pices 2 years ago at the ac boat show i put one in my tool box and screwed one to the top of a piling next to my boat the grain raised a little and it turned a shade darker in 2 years i got a price this year at the boat show if i make the templet and install my self $35 a sqft and thats all strait no 45s or pitcher framing so for my deak 10x9 90sqft =$3200 for that price im going real next year
User avatar
k9th
Ultimate User
Posts: 1615
Joined: Fri Oct 31, 2008 10:31 pm
Location: Michigan City, IN

Post by k9th »

I have researched it for use on SeaDog and like the product. I plan to install it in the future on the bridge where gray carpet exists today. My wife and I both agree that it will be just what we want.
Tim

"SeaDog"
1979 36' Tri-Cabin
rossjo
Ultimate User
Posts: 2799
Joined: Tue Nov 08, 2005 2:48 pm
Location: Charleston, SC
Contact:

Post by rossjo »

I love the NuTeak look as well, but my wife thinks it looks fake. Not sure how she can tell- maybe its just that she knows its plastic. Love the look and low maintenance.

I personally don't care, but won't be using it if the Commander disapproves \;-)/
Captain Ross, 2009 Trojan Boater of the Year
"Viva Mahia" F32 Cummins 6BTA diesels,
"Mack Attack" Chaparral 244 Fish, SeaPro 180, McKee 14, Montauk-17
Image
Post Reply